Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 12 | Manualshive

Page: 12 / 147

background image

• With more than one passenger. Allow a passenger to ride only in the

passenger seat.

• With weight (riders and cargo) that exceeds the maximum weight rating of the

vehicle. See the Manufacturing Information Label.

ALWAYS:

• Wear a full-face helmet (DOT-certified in USA) and eye protection that meets

or exceeds established safety standards. This vehicle is not equipped with
airbags.

•  Wear your seat belt.
•  Reduce speed on wet or slippery surfaces.
•  Keep both hands on the steering wheel when driving.
•  Make sure passenger reads and understands all safety labels.
•  Keep hands, arms and feet inside the vehicle.
•  Be aware of your surroundings and driving conditions.
•  Be prepared for changing weather conditions and dress accordingly.
•  Use only genuine SLINGSHOT accessories designed for your SLINGSHOT

vehicle.

SAFETY WARNINGS

WARNING

Failure to follow recommended precautions and procedures could result in

severe injury or death. Always heed all safety precautions and follow all

operation, inspection and maintenance procedures outlined in this manual.

This owner’s manual contains information that is essential to the safe use and
proper maintenance of your SLINGSHOT vehicle. Anyone who operates the
SLINGSHOT vehicle must read the owner’s manual and all safety labels on the
vehicle before operating.

• Anyone who operates the SLINGSHOT vehicle must have a valid driver’s

license with a motorcycle endorsement. Never allow anyone without a valid
driver’s license and motorcycle endorsement to operate this vehicle.

• Never allow anyone under the age of 16 to operate this vehicle.
• Never install a child safety seat in this vehicle. All riders must be tall enough to

sit with backs against the seat, both feet flat on the floor and seat belts
properly secured.

• The driver and passenger must wear a full-face DOT-approved helmet, eye

protection and seat belt at all times.

• Always keep hands, arms and feet inside the vehicle at all times.
• Avoid wearing long scarves and clothing that may trail outside the rider

compartment.

10

Downloaded from

«
...
10
11
12
13
14
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: EAL Pages: 4

Brand: Ford Pages: 12

Brand: Whispbar Pages: 16

Brand: Thule Pages: 12

Brand: Gator Pages: 2

Brand: BrandMotion Pages: 2

Brand: Ford Pages: 256

Brand: Huf Pages: 6

Brand: rough country Pages: 4

Brand: Volvo Pages: 197

Brand: Prorack Pages: 14

Brand: Yakima Pages: 12

Brand: Ford Pages: 2

Brand: Toyota Pages: 596

Brand: Kargo Master Pages: 10

Brand: Kia Pages: 4

Brand: Volkswagen Pages: 83

Brand: Sony Ericsson Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands