Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 106 | Manualshive

Page: 106 / 147

background image

LED LIGHT ASSEMBLIES

LED lights are not serviceable. If one of the LED lamps fails to illuminate, the
entire light assembly must be replaced.

1. Remove the rear body panel to access the light assembly.

2. Remove the screws

q

securing the light assembly to the vehicle (taillight

assembly shown).

3. Unplug the electrical connector

w

from the light assembly.

4. Remove the light assembly.

5. Install the electrical connector to the replacement light assembly.

6. Reinstall the light assembly. Tighten the screws.

TORQUE

3 ft-lbs (4 Nm)

7. Reinstall the rear body panel. Tighten the screws.

TORQUE

5.4 ft-lbs (7 Nm)

HEADLAMP AIM INSPECTION CONDITIONS

The following headlamp aim inspections and adjustments will be accurate only
when tire pressures and suspensions are at factory-recommended settings.
Refer to safety labels on the vehicle or to the specifications section beginning on
page 121. The vehicle must also be unladen (without fuel, rider weight or cargo
weight).

104

Downloaded from

«
...
104
105
106
107
108
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: CITROEN Pages: 52

Fleetwood Brougham Sedan 1966

Brand: Cadillac Pages: 56

Brand: Thule Pages: 8

Brand: Hama Pages: 13

OUTLANDER PHEV 2022

Brand: Mitsubishi MOTORS Pages: 8

Brand: Curt Group Pages: 3

Brand: Juna Pages: 10

Brand: 3UVIEW Pages: 15

GRAND CHEROKEE 4xe 2023

Brand: Jeep Pages: 440

Brand: Mahindra Pages: 247

Brand: RAM Pages: 196

AdvanceMobile VX1

Brand: AdvanceTec Pages: 20

Brand: Datsun Pages: 104

Brand: Advanced Keys Pages: 15

Brand: LINEACCESSORI Pages: 36

Brand: Zte Pages: 13

Brand: KRAM telecom Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands