Home
/
Polaris
/
RZR PRO R
/
Service Manual

Polaris RZR PRO R, Service Manual, Page: 499 / 508

Share

484 pages before
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508

Page: 499 / 508

Polaris RZR PRO R Service Manual Download Page 499

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

12.41

CAN SYSTEM

CAN SYSTEM OVERVIEW

The CAN system allows a large amount of information to
flow between components. The CAN system on this
vehicle will link the ECU, Diagnostic Connector,
Instrument Cluster/PIDD and EPS unit through a green
and a yellow wire.

CAN SYSTEM TESTING

A component not displaying information correctly could
be the cause of damaged CAN wiring or a faulty
component.

The easiest location to test the CAN system is at the
Diagnostic Connector.
Turn the key to the OFF position. Using a multimeter,
ohm across the Green and Yellow wires at the diagnostic
connector.

• A

RZR

equipped with a PIDD should have a reading of

120 Ω. Anything other than 120 Ω is bad.

• A

RZR

not equipped with a PIDD should see a reading

of 60 Ω. A reading of 120 Ω is bad.

«
...
497
498
499
500
501
...
»

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments