Polaris RZR PRO R Service Manual Download Page 488 | Manualshive

Page: 488 / 508

background image

12.30

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

FAN CONTROL CIRCUIT BYPASS TEST

1.

Disconnect

harness

from

coolant

temperature

sensor on the engine cylinder head (see Engine
Coolant

Temperature

Sensor

(ECT)

Overview

outlined in this chapter).

2.

With the transmission in Park, start the engine. After
a few seconds, the fan should start running and the
“Check Engine” indicator should display on the
instrument

cluster.

This

indicates

all

other

components are working properly.

3.

If the fan does not run or runs slowly, check the fan
motor wiring, ground, motor condition, circuit breaker
and mechanical relay for proper operation. Repair or
replace as necessary. If the fan runs with the sensor
harness disconnected, but will not turn on when the
engine is hot, check the coolant temperature sensor
and connector terminals.

COOLING FAN REPLACEMENT

REMOVAL

1. Drain cooling system.

2. Remove two fasteners

q

and remove the hood.

3. Remove one fastener

w

and remove the nose cone.

4. Remove thirteen fasteners

e

, one push-pin

r

, and

remove the front fender flare. Repeat for opposite
side of the vehicle.

«
...
486
487
488
489
490
...
»

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RZR PRO R

Brand: Bajaj Motorsport Pages: 8

Brand: KYMCO Pages: 1

Brand: Taylor-Dunn Pages: 111

Low Loader Trailer

Brand: Futura Pages: 20

Club Car Carryall 272

Brand: Ingersoll-Rand Pages: 44

Brand: Cushman Pages: 158

Brand: PROALL Pages: 59

2007 Outlander 500 EFI

Brand: Can-Am Pages: 148

Brand: Arctic Cat Pages: 9

Brand: Arctic Cat Pages: 24

Brand: Arctic Cat Pages: 92

Utility Vehicle

Brand: TOMCAR Pages: 150

Brand: NorthStar Pages: 24

Brand: SSR Motorsports Pages: 55

Brand: Rollplay Pages: 28

Brand: Yetti Pages: 42

Brand: KEEWAY Pages: 97

Brand: Century Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands