manualshive.com logo in svg

Polaris RZR PRO R, Service Manual

Share
Download
Polaris RZR PRO R Service Manual Download Page 450

11.20

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

BODY COMPONENT REMOVAL

SEATS

1. To remove a seat, lift upward on the release lever

q

located under the front of the seat.

2. Lift upward and forward on the seat while lifting up on

the release lever and remove seat from the vehicle.

REAR CLOSE-OFF PANEL

1. Remove seats.

2. Unlock six 1/4 turn latches (four on top panel, two on

bottom panel).

3. Unlock two 1/4 turn latches from the center console.

4. Lift upward and remove the top close-off panel, and

the bottom close-off panel.

BODY / FRAME

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands