manualshive.com logo in svg

Polaris RZR PRO R, Service Manual

Share
Download
Polaris RZR PRO R Service Manual Download Page 414

10.12

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

MASTER CYLINDER

MASTER CYLINDER REMOVAL

1. Locate the master cylinder

q

above the left front tire

in the wheel well area.

2. Remove the nut

w

from the fastener

e

that attaches

the master cylinder to the brake pedal lever.

3. Place a container to catch brake fluid under the

master cylinder brake line banjo bolts

r

.

CAUTION

Brake fluid will damage finished surfaces. Do not allow

brake fluid to come in contact with finished surfaces.

NOTICE

Make note of front and rear brake line locations to

master cylinder.

4. Loosen the brake line banjo bolts and allow fluid to

drain.

NOTICE

Dispose of fluid properly. Do not re-use.

5. Remove the two mounting fasteners

t

that secure

the master cylinder to the frame.

MASTER CYLINDER INSTALLATION

1. Install new stat-o-seal, rear brake line banjo fitting,

new stat-o-seal and banjo bolt to the rear port on the
master cylinder.

IMPORTANT

Lubricate seals with a thin film of DOT 4 brake fluid

prior to installation.

BRAKE SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands