manualshive.com logo in svg

Polaris RZR PRO R, Service Manual

Share
Download
Polaris RZR PRO R Service Manual Download Page 298

7.20

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

TRANSMISSION ASSEMBLY

1. Thoroughly clean the mating surfaces of the

transmission case halves so they are free of 3 Bond
sealant. Failure to properly clean the surfaces may
lead to transmission case leaks.

2. Install output shaft gear

o

.

3. Install front output shaft

i

into gear housing.

4. Install three idler gears

u

as an assembly.

5. Install transmission input shaft

y

.

6. Install the shift shaft and forks as an assembly.

7. Lift up on the shift shaft rail and move the rail

assembly rearward to allow the shift fork pins to be
installed onto the shift drum

t

. Install the shift drum

into the transmission housing.

8. Install the two sector gears.

TRANSMISSION

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands