Polaris RZR PRO R Service Manual Download Page 295

Page: 295 / 508

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

7.17

TRANSMISSION VENT LINE ROUTING

1. The transmission vent lines connect to two barb

fittings

on the front of the transmission.

2. One line routes across the transmission and is

secured with a hinge clip

3. Both lines join at a tee-fitting

above the

transmission.

4. The vent line terminates into a fitting

on the rear

sway bar mounting tube below the air box.

TRANSMISSION DISASSEMBLY

1. Drain transmission fluid.

2. Remove sixteen fasteners

and separate

transmission cover from the transmission.

NOTICE

Idler gear may come off with front transmission cover as

shown.

3. Remove idler gear from transmission cover.

4. Remove one fastener

and remove shift linkage

plate.

TRANSMISSION

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands