Polaris RZR PRO R Service Manual Download Page 275

Page: 275 / 508

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

6.25

5. Torque the three fasteners

to specification.

TORQUE

Helix Fasteners:

63 ft-lbs (85 Nm)

6. Once back together, verify the alignment marks made

during disassembly are properly aligned.

7. Install the stationary and movable sheave on the

vehicle. See Driven Clutch Installation.

DRIVEN CLUTCH INSTALLATION

1. Install driven clutch, bolt

, spacer

, and washer

. Torque fastener to specification.

TORQUE

Driven Clutch Retaining Bolt:

55 ft-lbs (75 Nm)

2. Install the drive belt.

3. Install outer clutch cover. Install five fasteners

and

engage 1/4 turn latches to secure the cover. Torque
fasteners to specification.

TORQUE

Outer PVT Cover Fasteners:

60 in-lbs (7 Nm)

PVT SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Brands by name

Popular brands