Polaris RZR PRO R Service Manual Download Page 268

Page: 268 / 508

6.18

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

4. Install the clutch cover

and clutch cover bolts

Hand tighten bolts.

5. Torque cover bolts in a cross pattern evenly to

specification.

TORQUE

Drive Clutch Cover Bolts:

15 ft-lbs (21 Nm)

DRIVE CLUTCH INSTALLATION

1. Install drive clutch stationary sheave.

2. Install drive clutch moveable sheave and drive clutch

retaining bolt

. Torque fastener to specification.

TORQUE

Drive Clutch Retaining Bolt:

Step 1: 140 ft-lbs (190 Nm)Step 2: Loosen two full

turns (720°)Step 3: 118 ft-lbs (160 Nm)

NOTICE

When drive clutch is fully installed, the spring coupler

between the engine and drive clutch may allow up to

approximately 30 degrees of free rotation when turning

clutch by hand. This rotation range is normal.

3. Install the drive belt.

4. Install outer clutch cover. Install five fasteners

and

engage 1/4 turn latches to secure the cover. Torque
fasteners to specification.

TORQUE

Outer PVT Cover Fasteners:

60 in-lbs (7 Nm)

PVT SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands