Home
/
Polaris
/
RZR PRO R
/
Service Manual

Polaris RZR PRO R, Service Manual

Share

Page: 193 / 508

Polaris RZR PRO R Service Manual Download Page 193

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

3.79

CRANKSHAFT REAR OIL SEAL
INSTALLATION

1. Remove excess sealer from seal recess.

IMPORTANT

Ensure the crankshaft is clean and free of any sealant.

2. Lubricate the outside diameter of the new crankshaft

seal with clean engine oil.

3. Using the

PU-52884

rear seal installer, press the new

crankshaft seal into the housing. The

PU-52884

also

establishes the depth of the seal in the crankshaft
seal bore.

CRANKSHAFT FRONT OIL SEAL
INSTALLATION

1. Install the seal into the front cover using the

PU-

52885

installer and the harmonic damper bolt. Insert

the harmonic damper bolt through the tool and the
seal, align the assembly with the crankshaft, and
thread the bolt in to the crankshaft to drive the seal
until fully seated in the front cover.

2. Ensure that the engine front cover is properly

supported when installing the seal.

ENGINE / COOLING SYSTEM

«
...
191
192
193
194
195
...
»

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands