manualshive.com logo in svg

Polaris RZR PRO R, Service Manual

Share
Download
Polaris RZR PRO R Service Manual Download Page 156

3.42

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

INSTALLATION

For timing chain installation see Camshaft Timing Chain
and Sprocket Installation page 3.90

TENSIONER SERVICE

REMOVAL

1. Remove three tensioner cover fasteners

w

and

tensioner cover.

IMPORTANT

The timing chain tensioner must be removed to unload

chain tension before the timing chain is removed.

NOTICE

The bottom fastener feature is slotted.

2. Remove chain tensioner fastener

e

and chain

tensioner.

ENGINE / COOLING SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands