Polaris RZR 570 2013 Service Manual Download Page 392 | Manualshive

Page: 392 / 482

background image

9.30

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

BRAKE BURNISHING PROCEDURE

It is required that a burnishing procedure be performed
after installation of new brake pads to extend service life
and reduce noise.

Start machine and slowly increase speed to 30 mph.
Gradually apply brakes to stop machine. Allow pads and
disc to cool sufficiently during the procedure. Do not
allow pads or disc to become hot or warping may result.
Repeat this procedure 10 times.

Do not make more

than 3 stops per 1 mile (1.6 km)

.

«
...
390
391
392
393
394
...
»

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RZR 570 2013

Brand: Yamaha Pages: 26

INDUSTRIAL 1200

Brand: Ezgo Pages: 148

Brand: E-TON Pages: 134

Brand: Landoll Pages: 76

Brand: Yamaha Pages: 21

Brand: Egholm Pages: 12

Brand: Hsun Pages: 150

Brand: Ventrac Pages: 93

Brand: Mahindra Pages: 100

Pioneer 1000 2017

Brand: Honda Pages: 307

Brand: Yamaha Pages: 173

Brand: MANCO Pages: 20

Brand: Taylor-Dunn Pages: 204

Polar Trailer LG 7

Brand: Clam Pages: 5

YFM350X Warrior

Brand: Yamaha Pages: 318

WORKMAN GTX 07131

Brand: Toro Pages: 48

Brand: Toro Pages: 52

Workman MDE 2008

Brand: Toro Pages: 130

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands