manualshive.com logo in svg

Polaris Ranger RZR SW, Service Manual, Page: 224 / 346

Share
Download
Polaris Ranger RZR SW Service Manual Download Page 224

7.8

FINAL DRIVE

Inner Plunging Joint / Boot Replacement

1.

Remove the front drive shaft from the vehicle (see
“FRONT DRIVE SHAFT - Removal”).

2.

Remove and discard the boot clamps.

3.

Remove the large end of the boot from the plunging joint
and slide the boot back.

4.

Use a soft-faced hammer or brass drift to separate the
plunging joint from the drive shaft. 

NOTE: If using a brass drift, be sure to tap on the
inner race of the joint only.

5.

Make sure the circlip remains on the shaft and not left in
the joint. Discard the circlip.

6.

Remove the boot from the drive shaft.

IMPORTANT: If the grease in the joint is obviously
contaminated with water and/or dirt, the joint should
be replaced.

7.

Thoroughly clean the joint with an appropriate solvent and
dry the joint to prevent any residual solvent from being left
in the joint upon reassembly.

8.

Visually inspect the joint by tilting the inner race to one side
to expose each ball. Severe pitting, galling, play between
the ball and its cage window, any cracking or damage to the
cage, pitting or galling or chips in raceways call for joint
replacement.

9.

Clean the splines on the end of the shaft and apply a light
coat of grease prior to reassembly.

10. Slide the small boot clamp and boot (small end first) onto

the drive shaft and position the boot in it’s groove machined
in the shaft.

11. Install a NEW circlip on the end of the shaft.

12. Grease the joint with the special joint grease provided in the

boot replacement kit. Fill the cavity behind the balls and the
splined hole in the joint’s inner race. Pack the ball tracks
and outer face flush with grease. Place any remaining
grease into the boot.

NOTE:  The amount of grease that’s provided is pre-
measured, so use all the grease.

13. Fully compress the joint and push the drive shaft firmly into

the inner race.

14. Align the circlip with the lead-in chamfer.

15. Use a soft-faced hammer to tap the joint onto the drive shaft

until it locks into place.

16. Pull on the joint to make sure it is securely locked into place.

17. Remove excess grease from the plunging joint’s external

surfaces and place the excess grease in the boot. 

18. Pull the boot over the joint and position the boot lips into

the grooves on the joint housing and shaft. Make sure the
boot is not dimpled or collapsed.

19. Install and secure the small clamp on the boot using the

“earless” clamp pliers.

20. Pull out on the drive shaft to center the joint in the housing.

Slide a straight O-ring pick or a small slotted screw driver
between the large end of the boot and the joint housing and
lift up to equalize the air pressure in the boot.

CV Boot Clamp Pliers

Earless Type: 8700226

CAUTION

Complete disassembly of the plunging joint is 

NOT recommended. The internal components 

are a precision fit and develop their own 

characteristic wear patterns. Intermixing the 

internal components could result in looseness, 

binding, and/or premature failure of the joint.

CAUTION

The grease provided in the replacement kit is 

specially formulated for wear resistance and 

durability. DO NOT use substitutes 

or mix with other lubricants.

Boot Replacement Grease Requirement:

Grease Service Kits

PN 1350059 (20g) / PN 1350046 (30g) / PN 1350047 (50g)

Inner Plunging Joint Capacity: 80g

CV Boot Clamp Pliers

Earless Type: 8700226

Summary of Contents for Ranger RZR SW



























































































































































































































































































































































Reviews:

No comments