Polaris RANGER CREW 900 2014 Manual Download Page 418 | Manualshive

Page: 418 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

10.33

BATTERY SERVICE

BATTERY SPECIFICATIONS

Battery PN 4014043 / 4014132-P

Type

Polaris Maintenance Free

Voltage

12 Vdc

Nominal Capacity
@ 20 HR Rate

32 AH

CCA - 2013 Models

Deka - 450
Johnson Controls - 575

CCA - 2014 Models

Johnson Controls - 575

Nominal Open
Circuit Voltage

12.8 Vdc or more.

Recommended
Charging Rate

1.8A @ 5-10 HR or 6.0A @ 1
HR

NOTE

Never attempt to open the battery.

GENERAL BATTERY INFORMATION

WARNING

CALIFORNIA PROPOSITION 65 WARNING:Batteries,

battery posts, terminals and related accessories contain

lead and lead compounds, and other chemicals known

to the State of California to cause cancer and birth

defects or other reproductive harm. WASH HANDS

AFTER HANDLING.

WARNING

Battery electrolyte is poisonous. It contains acid!

Serious burns can result from contact with the skin,

eyes, or clothing.ANTIDOTE:External: Flush with water.

Internal: Drink large quantities of water or milk. Follow

with milk of magnesia, beaten egg, or vegetable oil. Call

a physician immediately.Eyes: Flush with water for 15

minutes and get prompt medical attention.Batteries

produce explosive gases. Keep sparks, flame,

cigarettes, etc. away. Ventilate when charging or using

in closed space. Always shield eyes when working near

batteries.Keep out of reach of children.

1.

Check battery voltage with a volt/ohm meter. A fully
charged battery should be 12.8 V or higher.

2.

If the voltage is below 12.6 V, the battery will need to
be recharged (see “Charging Procedure”).

To service a Maintenance Free battery:

3.

Remove battery from the vehicle (see Chapter 2).

4.

Test battery with a voltage meter or load tester to
determine battery condition. This will determine the
length of time required to charge the battery to full
capacity. Refer to OCV table (see “OCV - Open
Circuit Voltage Test”).

5.

Charge the battery as recommended (see “Charging
Procedure”).

BATTERY TERMINAL BLOCK

The terminal block (A) is located under the hood near the
radiator pressure cap. The terminal block provides easy
hookup for accessories.

TORQUE

Terminal Block Nuts:

20-25 in-lbs (2.3-2.8 Nm)

«
...
416
417
418
419
420
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Brand: Jayco Pages: 87

1997 TRX300 Fourtrax 300

Brand: Honda Pages: 162

Brand: Taylor-Dunn Pages: 134

2009 Outlander 500 EFI

Brand: Can-Am Pages: 152

Brand: New Force Motor Pages: 54

Brand: E-Z-GO Pages: 84

Brand: Yamaha Pages: 92

Brand: Yerf-Dog Pages: 21

Brand: Xingyun Pages: 92

Brand: Range Road Pages: 21

Brand: Yamaha Pages: 185

GOOSENECK LIVESTOCK TRAILER

Brand: Merritt Pages: 37

Brand: Thump Pages: 78

Brand: Coleman Powersports Pages: 78

Brand: Coleman Pages: 119

OUTFITTER 700-L

Brand: Coleman Pages: 176

Brand: Toro Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands