Polaris RANGER CREW 900 2014 Manual Download Page 369

Page: 369 / 447

9.16

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

FRONT CALIPER SERVICE

CALIPER EXPLODED VIEW

CALIPER REMOVAL

Elevate and safely support the front of the vehicle.

Remove the (4) wheel nuts and the front wheel.

CAUTION

Use care when supporting vehicle so that it does not tip

or fall. Severe injury may occur.

Clean caliper area before removal.

Place a container below the caliper to catch brake
fluid when removing line. Remove brake line (A) from
caliper.

Loosen brake pad adjustment set screw (B) to allow
brake pad removal after the caliper is removed.

BRAKES

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands