Polaris RANGER CREW 900 2014 Manual Download Page 367 | Manualshive

Page: 367 / 447

background image

9.14

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

PAD INSPECTION

1.

Measure the thickness of the pad material. Replace
pads if worn beyond the service limit.

Front Brake Pad Thickness

New: .298 ± .007” (7.56 ± .178 mm)Service Limit: .180”

(4.6 mm)

PAD ASSEMBLY / INSTALLATION

1.

Lubricate mounting bracket pins with a light film of
silicone grease and install rubber dust boots.

2.

Compress mounting bracket and make sure dust
boots are fully seated. Install pads with friction
material facing each other.

WARNING

If brake pads are contaminated with grease, oil, or

liquid soaked do not use the pads. Use only new, clean

pads.

3.

Install caliper onto front hub and torque mounting
bolts to specification.

TORQUE

Front Caliper Mounting Bolts:

30 ft-lbs (41 Nm)

4.

Slowly pump brake pedal until pressure has been
built up. Maintain at least 1/2, (12.7 mm) of brake
fluid in reservoir to prevent air from entering brake
system.

«
...
365
366
367
368
369
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Formula Mx 1988

Brand: BOMBARDIER Pages: 62

traxter max series

Brand: BOMBARDIER Pages: 174

outlander max 800

Brand: BOMBARDIER Pages: 160

Brand: BOMBARDIER Pages: 282

Brand: Erde Pages: 4

Brand: Variant Pages: 16

FEBER quad KRIPTON

Brand: Famosa Pages: 4

Brand: Yamaha Pages: 42

Brand: KAYO MOTO Pages: 8

Brand: Ifor Williams Trailers Pages: 16

INTIMIDATOR XD 4

Brand: DFK Pages: 84

Brand: Equinox Systems Pages: 6

AUTOMIZER HELPING-HAND

Brand: Labrie Pages: 118

Brand: Baja motorsports Pages: 82

2010 California Roadster

Brand: ACG Pages: 53

Brand: Yamaha Pages: 287

Brand: Truxta Pages: 24

Hitch XA-71 Series

Brand: Holland Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands