Polaris RANGER CREW 900 2014 Manual Download Page 342

Page: 342 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

8.23

11. Install the bushing to the specified depth as shown.

Female Side Gear Bushing Replacement

12. Locate the bushing split. Using a small chisel or flat

blade screwdriver, peel back and remove the old
bushing from the side gear, being careful not to
damage the side gear.

13. Thoroughly clean the bore of the side gear and

check for any unwanted burs.

14. Press the new bushing into the side gear until it

bottoms out.

PLANETARY DIFFERENTIAL ASSEMBLY

Thoroughly clean the differential components.

Assemble the side gears and place them onto the
ring gear along with the (6) planet gears.

Align and install the differential cover using the
previously made scribe marks.

Apply Loctite® 2760 to cover screws.

TRANSMISSION

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands