Polaris RANGER CREW 900 2014 Manual Download Page 313 | Manualshive

Page: 313 / 447

background image

7.26

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

REAR DRIVE SHAFT

REMOVAL

1.

Follow steps 1-6 of “REAR BEARING CARRIER -
Removal” procedure.

2.

Remove the upper bearing carrier fastener and tilt
the carrier down while removing the end of the
driveshaft.

3.

With a short, sharp jerk, remove drive shaft from the
transmission.

4.

Refer to the “DRIVE SHAFT SERVICE” section if
repairing the drive shaft.

INSTALLATION

1.

Install a new spring ring (A) on the end of the drive
shaft if not replacing the drive shaft assembly. Apply
an anti-seize compound to the splines.

2.

Align splines of the drive shaft with the transmission
and reinstall the drive shaft. Use a rubber mallet to
tap on the outboard end of the drive shaft if
necessary.

3.

Insert the drive shaft into the bearing carrier and tilt
the carrier up.

4.

Install the upper bearing carrier fastener.

5.

Refer to “REAR BEARING CARRIER - Installation”
procedure to reassemble the vehicle.

«
...
311
312
313
314
315
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Trail Boss 330 Quadricycle

Brand: Polaris Pages: 119

Brand: Sealey Pages: 4

Off-Roader 36EL

Brand: Texas Pages: 27

Brand: Panther Pages: 16

Brand: HYOSUNG Pages: 133

Brand: Hsun Pages: 100

Brand: PRONAR Pages: 138

2014 RZR XP 1000

Brand: Polaris Pages: 474

Brand: Galaxy vans Pages: 60

Brand: Land Pride Pages: 96

Renegade 570 2016

Brand: Can-Am Pages: 534

Brand: Yamaha Pages: 52

WOLVERINE YFM350FXP

Brand: Yamaha Pages: 167

Brand: Yamaha Pages: 176

Brand: Yamaha Pages: 156

Brand: E-TON Pages: 38

Brand: TIMBCO Pages: 36

Brand: Portafill Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands