Polaris RANGER CREW 900 2014 Manual Download Page 308

Page: 308 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

7.21

12. Carefully install the LH output hub assembly into the

cover plate. Take care not to damage the new cover
plate seal while installing the output hub.

13. Install the output cover assembly onto the gearcase

housing. Install the (7) cover plate screws and torque
to specification.

TORQUE

Cover Plate Screws:7-11 ft-lbs (10-15 Nm)

FRONT GEARCASE INSTALLATION

Install the gearcase between the left-hand upper and
lower control arms into the frame.

Install the vent line on the gearcase and ensure it’s
routed properly.

Install the left front lower control arm grease zerk
fitting.

Install the propshaft onto the front gearcase.

Install new gearcase mounting bolts and torque to
specification.

TORQUE

Front Gearcase Mounting Bolts:

30 ft-lbs (41 Nm)

Drive a new roll pin into the front propshaft yoke.

Install the drive shafts into the front gearcase (see
“FRONT DRIVE SHAFT - Installation”).

FINAL DRIVE

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands