Polaris RANGER CREW 900 2014 Manual Download Page 297

Page: 297 / 447

7.10

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

PROPSHAFT U-JOINT SERVICE

DISASSEMBLY

Remove internal or external snap ring from all
bearing caps.

CAUTION

Always wear eye protection.

NOTE

If yoke or bearing is removed, cross bearing must be

replaced. Note orientation of grease fitting and mark

inner and outer yoke for correct re-positioning during

installation.

Support inner yoke as shown and drive outer yoke
down (bearing cap out) with a soft face hammer.

Support U-joint in vise as shown and drive inner yoke
down to remove remaining bearing caps.

Force U-joint cross to one side and lift out of inner
yoke.

FINAL DRIVE

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands