Polaris RANGER CREW 900 2014 Manual Download Page 267 | Manualshive

Page: 267 / 447

background image

6.18

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

BUTTON TO TOWER CLEARANCE
INSPECTION

1.

Inspect for any clearance between spider button to
tower. If clearance exceeds specification, replace all
buttons and inspect surface of towers. See “Spider
Removal” procedure.

Button to Tower Clearance:000-.005”

2.

Inspect sheave surfaces. Replace the entire clutch if
worn, damaged or cracked.

SPIDER REMOVAL

1.

Install clutch in holding fixture (PN 2871358-A) and
loosen the spider (counterclockwise) using Clutch
Spider Removal Tool (PN 2870341).

Clutch Holding Fixture: (PN 2871358-A)

Spider Removal Tool: (PN 2870341)

NOTE

To maintain proper clutch balance and belt-to-sheave

clearance, be sure to reinstall the original quantity and

thickness of washers/spacers beneath the spider during

assembly.

«
...
265
266
267
268
269
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Brand: Razor Pages: 2

Brand: Tru-Turf Pages: 70

Brand: Baja motorsports Pages: 82

Brand: wsm Pages: 25

Brand: Ski-Doo Pages: 159

Brand: Ski-Doo Pages: 103

Brand: Hisun Pages: 116

Brand: Yamaha Pages: 18

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 92

WARRIOR YFM350XN

Brand: Yamaha Pages: 167

Brand: Yamaha Pages: 227

Brand: Yamaha Pages: 288

Brand: Yamaha Pages: 360

Brand: Yamaha Pages: 439

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands