Polaris RANGER CREW 900 2014 Manual Download Page 192 | Manualshive

Page: 192 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

4.43

DIGITAL WRENCH® COMMUNICATION
ERRORS

If you experience problems connecting to a vehicle or
any Digital Wrench® related problem, visit the Digital
Wrench®

Knowledge

Base

for

the

most

current

troubleshooting

information,

FAQs,

downloads

and

software updates at:

http://polaris.diagsys.com/.

DIGITAL WRENCH® - DIAGNOSTIC
CONNECTOR

The diagnostic connector is located under the passenger
seat connected to a sealed plug. To access the
diagnostic connector on 2 seat models with a center
console the center console must be removed.

Follow these steps to connect the diagnostic interface
cable to the vehicle to allow Digital Wrench® use:

1.

Assemble the SmartLink Module and attach the PC
Interface Cable to your laptop (see page 4.3).

2.

Remove the protective cap from the Digital Wrench®
connector.

3.

Connect the Vehicle Interface Cable to the Digital
Wrench® diagnostic connector.

4.

Turn the ignition key to the ‘ON’ position, select the
appropriate vehicle and wait for the status to display
‘Connected’ in the lower left corner of the screen.

5.

Once

connected,

proceed

with

using

Digital

Wrench®.

DIGITAL WRENCH® SERIAL NUMBER
LOCATION

Open the configuration screen by clicking on the wrench
icon. The serial number is located on the right side of the
screen.

FUEL SYSTEM - GENERAL

«
...
190
191
192
193
194
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Brand: MANCO Pages: 5

Brand: FARMA Pages: 36

Brand: OTIS Pages: 17

Formula Mx 1988

Brand: BOMBARDIER Pages: 62

traxter max series

Brand: BOMBARDIER Pages: 174

outlander max 800

Brand: BOMBARDIER Pages: 160

Brand: BOMBARDIER Pages: 282

Brand: Dongfang Motor Pages: 19

Brand: Recon Pages: 102

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 92

WARRIOR YFM350XN

Brand: Yamaha Pages: 167

Brand: Yamaha Pages: 227

Brand: Yamaha Pages: 288

Brand: Yamaha Pages: 360

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands