Polaris RANGER CREW 900 2014 Manual Download Page 161 | Manualshive

Page: 161 / 447

background image

4.12

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

FUEL LINE REMOVAL / INSTALLATION

1.

Place a shop towel around the fuel line to catch any
dripping fuel.

2.

To remove either end of the fuel line, pull open tabs
while moving the connector out to release the line.

3.

Pull the fuel line outward to remove.

4.

To reinstall the line, verify the connections are clean
and free of debris.

5.

Place the fuel line back over the fitting and slide the
connector locking mechanism back into place. Verify
the connector tabs snap back into place by pulling
out lightly on connector.

6.

Be sure fuel line is routed and retained properly.

FUEL SYSTEM - GENERAL

«
...
159
160
161
162
163
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Brand: Hammerhead Off-Road Pages: 105

2005 TRX400EX Sportrax 400EX

Brand: Honda Pages: 238

QUAD - PART LIST 2007

Brand: GAS GAS Pages: 77

Brand: Toro Pages: 20

Can-Am 450 Series

Brand: BRP Pages: 196

Camoplast ATV T4S

Brand: CAMSO Pages: 10

Brand: TGB Pages: 269

Brand: TGB Pages: 306

Brand: Fort Pages: 88

Sportsman 800 Big Boss

Brand: Polaris Pages: 143

2010 Ranger RZR 800 EFI

Brand: Polaris Pages: 352

Junior Sport JS80IIR

Brand: Hammerhead Off-Road Pages: 31

Brand: Hammerhead Pages: 67

Brand: KAYO MOTO Pages: 186

Brand: Ifor Williams Trailers Pages: 55

Brand: Suzuki Pages: 508

2015 WILDCAT SPORT

Brand: Arctic Cat Pages: 68

Brand: Arctic Cat Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands