manualshive.com logo in svg

Polaris RANGER 1000 2020, Service Manual

The Polaris RANGER 1000 2020 Service Manual is a valuable resource for all owners of this powerful side-by-side vehicle. Easily download the manual for free from manualshive.com to ensure that you have the information you need to keep your RANGER running smoothly and efficiently.

Share
Download
background image

3.38

9850045 R01 - 2020-2021 RANGER 1000 Service Manual

© Copyright Polaris Inc.

5. Retract the plunger all the way in and install into the

cylinder.

IMPORTANT

Ensure the plunger and spring are not installed when

installing the tensioner.

6. Install the two mounting bolts. Torque fasteners to

specification.

TORQUE

Tensioner Mounting Fastener:

7 ft-lbs (10 Nm)

7. Install the plunger bolt. Torque fastener to

specification.

TORQUE

Plunger Bolt:

15 ft-lbs (20 Nm)

8. Turn the engine over by hand to ensure proper chain

tension is applied.

CAMSHAFT SPROCKET SERVICE

REMOVAL

1. Remove the valve cover. Refer to Valve Cover

Service page 3.35.

2. Remove the two fasteners

q

securing the camshaft

sprocket to the camshaft and slide the sprocket off
the camshaft.

NOTICE

Fasteners are one time use. Discard after removing.

INSTALLATION

1. Perform engine timing procedure. Refer to Engine

Timing page 3.32.

2. Reinstall the valve cover. Refer to Valve Cover

Service page 3.35.

ENGINE / COOLING / EXHAUST

Summary of Contents for RANGER 1000 2020



































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER 1000 2020

Cushman Haulster 84065 Parts & Maintenance Manual preview
Haulster 84065
Brand: Cushman Pages: 158
Yamaha GRIZZLY 700 2014 Owner'S Manual preview
GRIZZLY 700 2014
Brand: Yamaha Pages: 176
Yamaha VIKING VI 2021 Owner'S Manual preview
VIKING VI 2021
Brand: Yamaha Pages: 174
Suzuki LT-A450X Manual preview
LT-A450X
Brand: Suzuki Pages: 528
Hisun Motors HS800UTV 2014 Maintenance Handbook preview
HS800UTV 2014
Brand: Hisun Motors Pages: 361
Abbey Machinery Slurry Tanker Maintenance, Operating Instructions And Spare Parts List preview
Slurry Tanker
Brand: Abbey Machinery Pages: 72
DAELIM ET-250 Owner'S Manual preview
ET-250
Brand: DAELIM Pages: 26
Ultra-tow 14717 Owner'S Manual preview
14717
Brand: Ultra-tow Pages: 15
Polaris Ranger RZR SW Service Manual preview
Ranger RZR SW
Brand: Polaris Pages: 346
Mahindra ROXOR Operator'S Manual preview
ROXOR
Brand: Mahindra Pages: 100
Yamaha YFM35FAS Supplementary Service Manual preview
YFM35FAS
Brand: Yamaha Pages: 119
Yamaha Phazer PZ50X 2008 Supplementary Service Manual preview
Phazer PZ50X 2008
Brand: Yamaha Pages: 212
KYMCO 250 MAXXER Specifications preview
250 MAXXER
Brand: KYMCO Pages: 1
Yamaha RX10LTGTAX Service Manual preview
RX10LTGTAX
Brand: Yamaha Pages: 1664
Eagle EG6088K Operation Manual preview
EG6088K
Brand: Eagle Pages: 24
PIAGGIO Vespa Commercial Service Station Manual preview
Vespa Commercial
Brand: PIAGGIO Pages: 81
PIAGGIO 2012 MSS APE 50 Service Station Manual preview
2012 MSS APE 50
Brand: PIAGGIO Pages: 117
Polaris 2005 99 Ranger Owner'S Manual preview
2005 99 Ranger
Brand: Polaris Pages: 104

Brands by name

Popular brands

Load more brands