Polaris 2014 Sportsman 570 EF Service Manual Download Page 88

Page: 88 / 456

3.30

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

ENGINE SERVICE

Accessible Engine Components

The following components can be serviced or removed
with the engine installed:

• Camshaft

• Camshaft Sprockets

• Cylinder Head and Gaskets

• Cylinder and Gaskets

• Piston and Rings

• Flywheel

• Starter Motor / Idler Gear Asm

• Stator (Alternator)

• Thermostat

• Valve Cover

• Water Pump

• Camshaft Timing Chain and Guides

• Crankshaft Seal (PTO)

• Oil Pump / Oil Pump Sprocket or Chain

The following components require engine removal for
service:

• Counterbalance Shaft and Bearings

• Crankshaft and Bearings

• Crankcase

• Oil Pressure Regulator

• Oil Pump Pickup Assembly

Top-End Service (Engine in Chassis)

ALL of the top-end engine components can be serviced
while the engine is mounted in the chassis.

ENGINE

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands