Polaris 2014 Sportsman 570 EF Service Manual Download Page 372 | Manualshive

Page: 372 / 456

background image

9.28

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

SPORTSMAN REAR CALIPER

Removal and Inspection

1.

Clean caliper area before removal.

2.

Using a flare nut wrench, remove hand brake (inner)
and auxiliary brake (outer) lines (arrows). Place a
container to catch brake fluid draining from brake
lines.

3.

Remove the two caliper mounting bolts and the
caliper.

4.

Remove the slide bolt snap rings (A), the slide pins
(B), the bracket pad (C), and the brake pads (D).

5.

Remove the anvil bolts and separate caliper halves
and remove pistons with piston pliers.

6.

Remove seals and O-rings. Clean the O-ring
grooves.

7.

Clean disc, caliper body, and pistons with brake
cleaner or alcohol.

8.

Remove

the slide

bolt

bushings.

Inspect

the

bushings and O-rings and replace if necessary.

BRAKES

«
...
370
371
372
373
374
...
»

Summary of Contents for 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Sportsman 570 EF

Brand: Woodland Mills Pages: 68

Brand: Wilson Electronics Pages: 3

Brand: Jayco Pages: 102

Brand: Landoll Pages: 64

Brand: EBO Pages: 19

BIG BEAR 4X4 YFM40FP

Brand: Yamaha Pages: 168

Brand: Thumpstar Pages: 26

Brand: Toro Pages: 8

Brand: Toro Pages: 8

Brand: Toro Pages: 40

Brand: Toro Pages: 44

Carryall 272 2005

Brand: Club Car Pages: 48

Brand: Cobra Pages: 69

Brand: Centaur Pages: 450

Brand: Atlas Copco Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands