Polaris 2014 Sportsman 570 EF Service Manual Download Page 359

Page: 359 / 456

9.15

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

FRONT BRAKES

Pad Removal

Elevate and support the of the ATV.

CAUTION

Use care when supporting vehicle so that it does not tip

or fall. Severe injury may occur.

Remove the wheel.

Loosen pad adjuster screw 2-3 turns.

Remove caliper from mounting bracket.

Push caliper piston into caliper bore slowly using a
C-clamp or locking pliers with pads installed.

NOTE:

Brake fluid will be forced through

compensating port into master cylinder fluid
reservoir when piston is pushed back into
caliper. Remove excess fluid from reservoir as
required.

Push mounting bracket inward and slip outer brake
pad past edge. Remove inner pad.

BRAKES

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands