Polaris 2014 Sportsman 570 EF Service Manual Download Page 327

Page: 327 / 456

8.9

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

13. Install

the

rear

wheel

nuts

and

torque

specification.

Rear Wheel Nut:

Refer to Chapter 2

14. With the ATV on level ground, add Polaris AGL Plus

Gearcase Lubricant to the proper level. See Chapter
2

for

proper

fill

procedures

and

Torque

Specifications.

Polaris AGL Gearcase Lubricant

(PN 2878068) (12 oz.)

(PN 2878069) (Gallon)

Troubleshooting Checklist

Check the following items when shifting difficulty is
encountered.

• Idle speed adjustment

• Transmission oil type/quality

• Drive belt deflection

• *Worn, broken or damaged internal transmission

components

TRANSMISSION

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands