Polaris 2014 Sportsman 570 EF Service Manual Download Page 299

Page: 299 / 456

7.17

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

FRONT DRIVE (CV) SHAFT

Inspection

Check the front and rear drive shaft CV boots for any
tears or leaking grease. If the drive shaft boot loses all
grease, CV joint failure will occur.

Removal

Set the ATV in park. Remove hub dust cap (if
equipped).

Remove cotter pin.

Loosen - but do not remove - the hub retaining nut.

Loosen - but do not remove - the wheel nuts.

Safely lift and support the front of the ATV.

CAUTION

Serious injury could occur if machine tips or falls.

Remove wheel.

Remove the two brake caliper attaching bolts.

CAUTION

Do not hang the caliper by the brake line. Use wire to

hang the caliper to prevent possible damage to the

brake line.

Remove hub nut and hub assembly.

Remove cotter pin and nut from lower A-arm ball
joint.

FINAL DRIVE

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands