Polaris 2014 Sportsman 570 EF Service Manual Download Page 259

Page: 259 / 456

6.25

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

DRIVE CLUTCH BUSHING SERVICE (NON EBS AND EBS)

Bushing Service

IMPORTANT: Special Tools Required

EBS Clutch Bushing Tool Kit - 2201379

ITEM

QTY.

PART #

TOOL DESCRIPTION

A, B

5132027

EBS Puller Tool

5132501

EBS Puller Nut

5132029

EBS Main Adapter

5132028

EBS Bushing Removal
Tool Instructions

–

9915111

Instructions

Additional Special Tools

QTY.

PART #

TOOL DESCRIPTION

2871226

Clutch Bushing Replacement Tool
Kit

2870386

Piston Pin Puller

*Clutch Bushing Replacement Tool Kit (PN 2871226

)

ITEM

QTY.

PART #

TOOL DESCRIPTION

5020628

P-90 Drive/Driven
Clutch Bushing Install
Tool

5020629

Drive Clutch Cover
Bushing Removal/
Installation Tool (all
clutches)

5020631

P-90 Driven Clutch
Cover Bushing
Removal Tool

5020632

Main Puller Adapter

5010279

Adapter Reducer

#10

5020633

Number Two Puller
Adapter

Bosch Automotive Service Solutions: 1-800-328-6657 or
http://polaris.service-solutions.com

NOTE: Bushings are installed at the factory using
Loctite™. In order to remove bushings it will be
necessary to apply heat evenly to the area around
each bushing. Clean all residual Loctite™ from
bushing bore prior to installing new bushing.

CAUTION

Clutch components will be hot! In order to avoid serious

burns, wear insulated gloves during the removal

process.

Moveable Sheave - Bushing Removal

Remove clutch as outlined previously in this chapter.

Install handle end of the Piston Pin Puller

(PN

2870386)

securely into bench vise and lightly grease

puller threads.

Piston Pin Puller (PN 2870386)

Remove nut from puller rod and set aside.

CLUTCHING

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands