Polaris 2014 Sportsman 570 EF Service Manual Download Page 178

Page: 178 / 456

4.32

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

ECT Sensor Replacement

Remove the seat and right side panel .

Remove the PVT outlet ducting to access the ECT
sensor.

Drain coolant to level below sensor.

Disconnect sensor from engine harness (1).

Using a wrench, remove and replace the sensor (2),
applying a light coating of thread sealant to aid
installation.

Torque the sensor to specification.

ECT:

17 ft-lbs (23 Nm)

Add the required amount of coolant and properly
bleed the cooling system.

FUEL SYSTEM - GENERAL

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands