Polaris 2014 Sportsman 570 EF Service Manual Download Page 125

Page: 125 / 456

3.67

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Valve Cover Installation

Apply Anti-seize and install the spark plug (A) and
torque to specification.

Spark Plug:

14 ft-lbs (19 Nm)

Prepare valve cover sealing surfaces by cleaning
thoroughly to remove all residue.

Apply a small amount of crankcase sealant to the
cylinder head half-moon cutouts (E) as shown.

Crankcase Sealant: 2871557

Install a

new

valve cover seal (B).

Install the (3) valve cover shoulder bolts (C) and
isolators (D) using a T40 driver.

Torque valve cover bolts to specification.

Valve Cover Bolts:

9 ft-lbs (12 Nm)

ENGINE

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands