background image

56

OPERATION

Hauling Cargo

Overloading the vehicle or carrying or towing cargo improperly can alter vehicle 

handling and may cause loss of control or brake instability, which can result in 

serious injury or death. Always follow these precautions when hauling cargo:
REDUCE SPEED AND ALLOW GREATER DISTANCES FOR BRAKING 

WHEN HAULING CARGO.
NEVER EXCEED THE MAXIMUM WEIGHT CAPACITY of the vehicle. When 

determining the weight you are adding to the vehicle, include the weight of the 

operator, accessories, loads in the rack or box and the load on the trailer tongue. 

The combined weight of these items must not exceed the maximum weight 

capacity.
CARGO WEIGHT DISTRIBUTION should be 1/3 on the front rack and 2/3 on 

the rear rack. When operating over rough or hilly terrain, reduce speed and 

cargo to maintain stable driving conditions. Carrying loads on only one rack 

increases the possibility of vehicle overturn.
CARRY LOADS AS LOW ON THE RACKS AS POSSIBLE. Carrying loads high 

on the racks raises the center of gravity of the vehicle and creates a less stable 

operating condition.
SECURE ALL LOADS BEFORE OPERATING. Unsecured loads can create 

unstable operating conditions, which could result in loss of control of the vehicle.
OPERATE ONLY WITH STABLE AND SAFELY ARRANGED LOADS. When 

handling off-centered loads that cannot be centered, securely fasten the load 

and operate with extra caution. Always attach the tow load to the hitch point 

designated for your vehicle.
HEAVY LOADS CAN CAUSE BRAKING AND CONTROL PROBLEMS. Use 

extreme caution when applying brakes with a loaded vehicle. Avoid terrain or 

situations that may require backing downhill.
USE EXTREME CAUTION when operating with loads that extend over the rack 

sides. Stability and maneuverability may be adversely affected, causing the 

vehicle to overturn.
DO NOT BLOCK THE FRONT HEADLIGHT BEAM when carrying loads on the 

front rack.
DO NOT TRAVEL FASTER THAN THE RECOMMENDED SPEEDS. Vehicle 

should never exceed 10 mph (16 kph) while towing a load on a level surface. 

Vehicle speed should never exceed 5 mph (8 kph) when towing loads in rough 

terrain, while cornering, or while ascending or descending a hill.

WARNING

Summary of Contents for 2009 Scrambler 500 4X4




































































































































Reviews: