manualshive.com logo in svg

Polaris 2007 SPORTSMAN 700 X2 EFI, Service Manual

The Polaris 2007 SPORTSMAN 700 X2 EFI is a high-performing off-road vehicle, perfect for adventure seekers. To ensure smooth maintenance and repairs, a comprehensive Service Manual is available for free download on our website. Dive into the details and download the manual today at manualshive.com.

Share
Download
background image

10.38

ELECTRICAL

Troubleshooting

Starter Motor Does Not Run

• Battery discharged - Low specific gravity

• Loose or faulty battery cables or corroded connections 

(see Voltage Drop Tests)

• Related wiring loose, disconnected, or corroded

• Poor ground connections at battery cable, starter motor 

or starter solenoid (see Voltage Drop Tests)

• Faulty key switch

• Faulty kill switch

• Faulty starter lockout function

• Faulty starter solenoid or starter motor

• Engine problem - seized or binding (Can engine be 

rotated easily?)

Starter Motor Turns Over Slowly

• Battery discharged - low specific gravity

• Excessive circuit resistance - poor connections (see 

Voltage Drop Test)

• Engine problem - seized or binding (Can engine be 

rotated easily?)

• Faulty or worn brushes in starter motor

Starter Motor Turns - Engine Does Not Rotate

• Faulty starter drive

• Faulty starter drive gears or starter motor gear

• Faulty flywheel gear or loose flywheel

Voltage Drop Test

The Voltage Drop Test is used to test for bad connections.  When
performing the test, you are testing the amount of voltage drop
through the connection.  A poor or corroded connection will
appear as a high voltage reading.  Voltage shown on the meter
when testing connections should not exceed .1 VDC per
connection or component.

To perform the test, place the meter on DC volts and place the
meter leads across the connection to be tested.  Refer to the
voltage drop tests on the starter system in this chapter.

Starter Motor Removal / Disassembly

NOTE:  Use electrical contact cleaner to clean starter
motor parts.  Some solvents may leave a residue or
damage internal parts and insulation.

1.

Remove the starter from the engine.

2.

Remove the two bolts, washers, and sealing O-Rings.
Inspect O-Rings and replace if damaged.

NOTE: Note the alignment marks on both ends of
the starter motor casing.  These marks must align
during reassembly.

Voltage should not exceed

.1 DC volts per connection

Summary of Contents for 2007 SPORTSMAN 700 X2 EFI










































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 SPORTSMAN 700 X2 EFI

KAYO MOTO A180 Assembly Manual preview
A180
Brand: KAYO MOTO Pages: 9
ODES Dominator Owner'S Manual preview
Dominator
Brand: ODES Pages: 136
Trolla 13030 Assembly Instructions Manual preview
13030
Brand: Trolla Pages: 11
ABI Attachments Workman XL Owner'S Manual preview
Workman XL
Brand: ABI Attachments Pages: 28
Apogee Adapt-X 300 User Manual preview
Adapt-X 300
Brand: Apogee Pages: 24
TGB BLADE 1000 EPS IRS 4X4 Assembly Manual preview
BLADE 1000 EPS IRS 4X4
Brand: TGB Pages: 16
Kubota R430 Operator'S Manual preview
R430
Brand: Kubota Pages: 112
Taylor-Dunn ET 3000 Manual preview
ET 3000
Brand: Taylor-Dunn Pages: 216
Yamaha WOLVERINE YXE70WPXH Owner'S Manual preview
WOLVERINE YXE70WPXH
Brand: Yamaha Pages: 186
Yamaha VX600ERC Owner'S Manual preview
VX600ERC
Brand: Yamaha Pages: 87
Yamaha YFM90 2019 Owner'S Manual preview
YFM90 2019
Brand: Yamaha Pages: 126
Husqvarna 2007 HUV 4213-G Owner'S Manual preview
2007 HUV 4213-G
Brand: Husqvarna Pages: 48
Yamaha YT175J Condensed Service Data preview
YT175J
Brand: Yamaha Pages: 10
Yamaha YFM660FP 2001 Assembly Manual preview
YFM660FP 2001
Brand: Yamaha Pages: 30
Yamaha WARRIOR YFM350XP Supplementary Service Manual preview
WARRIOR YFM350XP
Brand: Yamaha Pages: 29
woodmizer STRB-S Safety, Operation, Maintenance & Parts Manual preview
STRB-S
Brand: woodmizer Pages: 46
Toro WORKMAN GTX 07131 Operator'S Manual preview
WORKMAN GTX 07131
Brand: Toro Pages: 48
Toro 7363 Operator'S Manual preview
7363
Brand: Toro Pages: 52

Brands by name

Popular brands

Load more brands