pleasant hearth PH35PS-B Owner'S Manual Download Page 31

Page: 31 / 44

[email protected]

7077-801F • 08/20

E. Alternate Masonry

D. Masonry

Non-combustible

Hearth Pad

Airtight Clean-out Door

Sheathing

2 in. (5.08mm) Minimum

Flashing

6 in.

(152mm)

Minimum

Fireclay Flue Liner

with Airspace

Concrete Cap

Non-combustible Hearth Pad

Airtight

Clean-Out Door

Clean-Out

Sheathing

3 in. (76mm) Minimum

1 in. (25mm) Clearance

Flashing

Fireclay flue

Liner with Airspace

Concrete Cap

1 in. (25mm) Clearance

with Firestop

6 in. (152mm)

Minimum

Fire Risk

Inspection of Chimney:

•

Masonry chimney must be in good condition.

•

Meets minimum standard of

NFPA 211

•

Factory-built chimney must be minimum 6

inch (152mm)

UL103 HT

WARNING

Improper installation, adjustment, alteration, service

or maintenance can cause injury or property damage.

Refer to the owner’s information manual provided with

this appliance. For assistance or additional information

consult a qualified installer, service agency or your dealer.

WARNING

Summary of Contents for PH35PS-B













































Search results

Summary of Contents for PH35PS-B

Reviews:

Related manuals for PH35PS-B

Brands by name

Popular brands

pleasant hearth PH35PS-B, Owner'S Manual

Search results

Summary of Contents for PH35PS-B

Reviews:

Related manuals for PH35PS-B

Brands by name

Popular brands