Planet WNAP-1260 User Manual Download Page 130

Page: 130 / 154

User’s Manual of WNAP-1260

-122-

Chapter 10. Web Configuration for the Client Mode

10.1. Client Mode Topology

In Client Mode, the WNAP-1260 is supposed to act as a wireless station for the PC or other wired-only
network device. Users can site survey the available local AP and choose someone to connect with.

10.2. Hardware Setting

Set the three-way switch on the side panel to

Client

after WNAP-1260 is powered on.

10.3. Running Status

Running Status

and the extended navigation menu is shown as follows:

Click the submenu to enter a specific configuration page.

10.3.1. System Status

Choose

Running Status

System Status

and the

System Status

page is displayed.

Summary of Contents for WNAP-1260



























































































































































Search results

Summary of Contents for WNAP-1260

Reviews:

Related manuals for WNAP-1260

Brands by name

Popular brands

Planet WNAP-1260, User Manual

Search results

Summary of Contents for WNAP-1260

Reviews:

Related manuals for WNAP-1260

Brands by name

Popular brands