manualshive.com logo in svg

Planet POE-1200G, User Manual

Share
Download
Planet POE-1200G User Manual Download Page 12

User’s Manual of POE-1200G / POE2400G

 

 

The PoE Injector Hub is a power-required device, it means, it will not work till it is powered. If your 
networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your 
device. It will prevent you from network data loss or network downtime. 

In some area, installing a surge suppression device may also help to protect your device from being 
damaged by unregulated surge or current to the PoE Injector Hub or the power adapter. 

 

2.2 Installing the PoE Injector Hub 

This section describes how to install your PoE Injector Hub and make connections to the PoE Injector Hub. Please read the 

following topics and perform the procedures in the order being presented. PLANET PoE Injector Hub do not need software 

configuration. To install the PoE Injector Hub on a desktop or shelf, simply complete the following steps. 

2.2.1 Desktop Installation 

To install a PoE Injector Hub on a desktop or shelf, simply complete the following steps: 

Step1: Attach the rubber feet to the recessed areas on the bottom of the PoE Injector Hub. 

Step2: Place the PoE Injector Hub on a desktop or shelf near an AC power source.  

Step3: Keep enough ventilation space between the PoE Injector Hub and the surrounding objects. 

 

 

When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 
1, Section 5, in Specification. 

 

Step4:

 Connect your PoE Injector Hub to network 802.3af powered devices (PD) and Switch. 

A. 

Connect one end of a standard network cable to the upper stack 10/100/1000 RJ-45 ports on the front of the PoE 
Injector Hub. 

B. 

Connect the other end of the cable to the 802.3 powered devices (PD) such as IP phone, wireless access point, 
IP camera, splitter, or switch etc. 

C. 

Connect the one end of a standard network cable to the relative lower stack 10/100/1000 RJ-45 port on the front 
of the  PoE Injector Hub. 

D. 

Connect the other end of the cable to the port of Switch. 

 

 

Connects to the PoE Injector Hub require UTP Category 5e/6 network cabling with RJ-45 tips. For 
more information, please see the Cabling Specification in Appendix A. 

 

Step5: 

Supply power to the PoE Injector Hub.

 

A. 

Connect one end of the power cable to the PoE Injector Hub. 

B. 

Connect the power plug of the power cable to a standard wall outlet. 

When the PoE Injector Hub receives power, the Power LED should remain solid Green. 

12 

Summary of Contents for POE-1200G


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands