Planet MAP-3100 Software Manual Download Page 71

Page: 71 / 124

PLANET Mesh Network Manager Guide

5.3.1.5

Network > WAN

Define the type of WAN interface to use. Three options are available: Static, DHCP, and

PPPoE. If user wishes to change the type to dynamic, select the DHCP, then click the

Save

Changes

button. If Static or PPPoE is selected instead, the

Configure

button will lead the

user to the configuration page of the type.

•

Network > WAN > Static

Enter the Static IP Address and its netmask, click the

Save Changes

button to activate the

Static WAN interface type. Hit the

Back

to go back to the WAN Type configuration page.

Parameters:

1) IP

Address

•

The static IP Address for the WAN interface

•

Data type: IP Address

PLANET Mesh Network Manager Guide

Page71 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands