background image

 

Field 

Description 

Enable 

Check the box to enable the RA mode. 

M flag/O flag 

The different flag combination can change the IPv6 IP 
address assign mode.The direction as below: 
 

M=1, O=0 or 1:

The PC will obtained the prefix and DNS from 

DHCPv6 (Stateful DHCPv6) 
 

M=0, O=1: 

The PC will use the prefix in RA

but the DNS will 

obtained by DHCPv6 (Stateless DHCPv6) 
 

M=0, O=0:

 The PC will obtained the prefix but not obtained 

the DNS (Stateless auto configuration) 

Max Interval 

The max RA release time interval, the default is 600 seconds.

Min Interval 

The min RA release time interval, the default is 200 seconds.

Prefix mode   

You can select the Auto or Manual. 

Prefix Address  Type the Prefix address on this item. 

Prefix Length 

Means the network ID length, the range is 16-64 bit. 

Preferred 
Time 

It must be small than or equal to the valid time, if it due, the 
IPv6 address can’t active create the new connect 

Valid Time 

The keep valid status time. 

 

The following table describes the 

DHCPv6 setting 

parameters of this page: 

Field 

Description 

DHCPv6 Mode 

You can select the None, Auto mode or Manual mode. 

IPv6 Address Pool 

You can set the IPv6 address pool on this item. 

Prefix Length 

Means the network ID length, the default value is 64 bit. 

Preferred Time 

It must be small than or equal to the valid time, if it due, 
the IPv6 address can’t active create the new connect 

Valid Time 

The keep valid status time, default value is 120 seconds 

DNS servers 

You can set the DNS server on this item, the default 
value is fe80::1.   

 

3.4.1.3 DHCP 

Dynamic Host Configuration Protocol (DHCP) allows the individual PC to obtain the 

TCP/IP configuration from the centralized DHCP server. You can configure this router as a 

DHCP server or disable it. The DHCP server can assign IP address, IP default gateway, 

and DNS server to DHCP clients. This router can also act as a surrogate DHCP server 

(DHCP proxy) where it relays IP address assignment from an actual real DHCP server to 

clients. You can enable or disable DHCP server or DHCP proxy. 

Click 

DHCP 

in the left pane, the page shown in the following figure appears. 

 

                                                                                                                       28

Summary of Contents for ADE-4400


































































Reviews: