Planet 802.11n Wireless PCI Adapter WNL-9330 User Manual Download Page 37

Page: 37 / 61

WMM - Power Save Enable

Enable WMM power saving mode to save energy and lets your

battery live longer.

Setting...

Click this button to select the WMM data type which will suppress

the function of power saving. When this kind of data is

transferring, power saving function will be disabled. Available data

types are AC_BK (Background / Low Priority), AC_BE (Best

Effort), AC_VI (Video First), and AC_VO (Voice First).

Direct Link Setup Enable

Enable or disable direct link setup (DLS) function. This function

will greatly improve the data transfer rate between WMM-enabled

wireless devices. Please click ‘Apply’ button on the right of this

check box after you check or uncheck this box, so corresponding

settings in this window will be activated or deactivated

respectively.

MAC Address

Input the MAC address of another WMM-enabled wireless device

you wish to establish a direct link here, then click ‘Apply’ to add

this MAC address to DLS address table.

Timeout Value

Input the timeout value of this WMM-enabled direct link wireless

device. If the wireless device is not responding after this time, it

will be removed from DLS table.

Tear Down

If you want to remove a specific wireless device from DLS table,

select the device and click this button to remove it.

Note: This function does not support in Windows VISTA.

3-6 WPS Configuration

Wi-Fi Protected Setup (WPS) is the latest wireless network technology which makes wireless

network setup become very simple. If you have WPS-enabled wireless access point, and you

want to establish a secure connection to it, you don’t have to configure the wireless access

point and setup data encryption. All you have to do is go to the WPS setup page of this

wireless card, click a button, and then press a specific button on the wireless access point you

wish to establish a secure connection - just three simple steps!

The WNL-9330 is compatible with WPS. To use this function, the wireless access point you

wish to connect to must support WPS function too. Now, please follow the instructions to

establish secure connection between WPS-enabled access point and your wireless card:

Summary of Contents for 802.11n Wireless PCI Adapter WNL-9330






























































Search results

Summary of Contents for 802.11n Wireless PCI Adapter WNL-9330

Reviews:

Related manuals for 802.11n Wireless PCI Adapter WNL-9330

Brands by name

Popular brands

Planet 802.11n Wireless PCI Adapter WNL-9330, User Manual

Search results

Summary of Contents for 802.11n Wireless PCI Adapter WNL-9330

Reviews:

Related manuals for 802.11n Wireless PCI Adapter WNL-9330

Brands by name

Popular brands