manualshive.com logo in svg

Planet Networking & Communication wnap-7325, User Manual, Page: 72 / 95

Share
Download
Planet Networking & Communication wnap-7325 User Manual Download Page 72

User Manual of WNAP-7325/WNAP-7335 

 

-71- 

5.4.2  Wireless Information 

Click “

Device

 

Status

” 

 “

Wireless Information

” and the following page will be displayed. 

 

 

Figure 5-49

 Wireless Information 

 

The page includes the following fields: 

Object 

Description 

 

Operation Mode 

Displays current Operation Mode. 

 

Physical address 

Displays AP’s Wireless MAC address. 

 

SSID 

It is the wireless network name. The default SSID is 

WNAP-7325 

or

 WNAP-7335

. 

 

Band 

Displays operating channel width which is 

Auto Select

, 

5G 

11NA HT20

 or

 5G 11NA HT40

. 

 

Radio Channel 

Displays the channel you would like to use. The channel range 

will be changed by selecting a different domain. 

 

Wireless Encryption 

Displays the encryption type that you would like to use. 

 

Transmit Power 

Display the TX power that you would like to use. 

 

Summary of Contents for wnap-7325
































































































Reviews:

No comments