manualshive.com logo in svg

Planet Networking & Communication wnap-7325, User Manual, Page: 58 / 95

Share
Download
Planet Networking & Communication wnap-7325 User Manual Download Page 58

User Manual of WNAP-7325/WNAP-7335 

 

-57- 

5.1.18 MAC Filtering Settings 

Click “

Operation Mode

” 

  “

AP Router

” or “

Wireless ISP

” and then enter the “

Mac Filtering Settings

” by 

clicking the 

Setup

 button next to it. This section allows you to configure the MAC filtering settings. 

 

Figure 5-30

 Mac Filtering Settings 

 

Object 

Description 

 

Filtering 

Enable or disable Mac Filtering. 

 

Mac Address 

Enter the Mac address to be filtered. 

 

Comment 

Set a name for the rule. 

 

 

5.1.19 Bandwidth Control 

Click “

Operation Mode

” 

 “

AP Router

” or “

Wireless ISP

” and then enter the “

Bandwidth Control

” by clicking 

the 

Setup

 button next to it. This section allows you to configure the bandwidth control. 

 

 

Figure 5-31

 Bandwidth Control Settings 

 

Object 

Description 

 

Quality of   

Enable or disable the QoS service. 

Summary of Contents for wnap-7325
































































































Reviews:

No comments