Planet Networking & Communication wnap-7325 User Manual Download Page 50

Page: 50 / 95

User Manual of WNAP-7325/WNAP-7335

-49-

5.1.11 Dynamic DNS Settings

Click “

Operation Mode

”



“

AP Router

” or “

Wireless ISP

” and then enter the “

Dynamic DNS Settings

” by

clicking the

Setup

button next to it. This section allows you to configure the DDNS settings.

Figure 5-23

Dynamic DNS Settings

Object

Description



DDNS option

Disable:

Disable DDNS function

Enable Easy DDNS:

Enable PLANET Easy DDNS

Enable Dynamic DDNS:

You are allowed to modify the DDNS

settings.



Dynamic DNS Provider

Select a server provider or disable the existing server.



Account

Enter the DDNS user name of the DDNS account.



Password

Enter the DDNS password of the DDNS account.



DDNS

Enter the host name or domain name provided by DDNS
provider.

Example of Planet DDNS Settings:

Please go to

http://www.planetddns.com/

to register a Planet DDNS account.

Please refer to the FAQ (

http://www.planetddns.com/index.php/faq

) for how to register a free account.

Summary of Contents for wnap-7325
































































































Search results

Summary of Contents for wnap-7325

Reviews:

Planet Networking & Communication wnap-7325, User Manual, Page: 50 / 95

Search results

Summary of Contents for wnap-7325

Reviews: