manualshive.com logo in svg

Planet Networking & Communication ICA-3260, User Manual, Page: 14 / 88

Share
Download
Planet Networking & Communication ICA-3260 User Manual Download Page 14

 

60fps Full HD IR Bullet IP Camera 

ICA-3260

 

mode or orange in the wireless mode. 

2.3 Initial Utility Installation 

This chapter shows how to quickly set up your IP camera. The camera is with the default 
settings. However to help you find the networked camera quickly, the windows utility PLANET 
IP Wizard II can search the cameras in the network that can help you to configure some basic 
setting before you start advanced management and monitoring. 

1.  Insert the bundled CD into the CD-ROM drive to launch the auto-run program. Once 

completed, a welcome menu screen will appear. 

2.  Click the “IP Wizard II” hyperlink and a dialog box will appear as shown below. 

If the welcome screen does not appear, click “Start” at the taskbar. Then, 
select “Run” and type “D:\Utility\IPWizard II\setup.exe”, assuming D is your 
CD-ROM drive. 

 

 

 

3.  The “Welcome to the Install Shield Wizard for PLANET IP Wizard II” prompt will be 

displayed on the screen and click “

Next

” to continue. 

 

 

4.  Please click “

Next

” to install with original settings, or you may click “

Change…

” button to 

modify the install folder and then press “Next” to continue. 

 

10

Summary of Contents for ICA-3260

























































































Reviews:

No comments