BIG BUCK INSTRUCTIONS
FOR MODELS 7033 & 7034
Thanks for buying these Planet Bike fenders. We design them
to make you want to steer your bike towards big puddles and
get through them with a smile. Failure to follow installation
instructions can result in loss of control, damage, personal
injury or death. If you are unsure of any part of the installation
process, please consult a qualified bicycle mechanic or local
bike shop. If you have any questions regarding installation of
the fenders, feel free to check out the FAQs at
www.planetbike.com or email us at [email protected].
©2015 Planet Bike. All Rights Reserved.
www.planetbike.com
BIG BUCK REAR FENDER INSTALLATION
WARNINGS
STEP 1: Open Cam lever/strap
assembly and lengthen or shorten
strap until you achieve a snug fit
around your seatpost.
STEP 1
STEP 2: You can adjust the angle of the
fender by using the knob on the bracket and
locating bracket higher or lower on the
seatpost. Be sure to have a minimum of 2
inches of clearance between fender and tire.
Note, for a clean look, extra strap can be
folded back into bracket.
For the most up to date
installation instructions go to
www.planetbike.com/page/support/manuals
GOOD GEAR GUARANTEE
BIG BUCK FRONT FENDER INSTALLATION
FOR SUSPENSION OR RIGID FORKS
STEP 1: Your Big Buck front fender comes with three different sized expansion
collars to fit a range of fork steerer tube sizes. Determine the correct size collar for
your fork. The most common size (7/8 – 1”) comes pre-installed.
STEP 2: Assemble collar and fender brackets as shown. Be sure to align raised
blocks on bottom of collar with slot on bracket.
STEP 3: Remove front wheel to make installation easier. With the fender assembled,
insert collar into the underside of the fork head tube and align with the tire. Adjust
position of the fore and aft fender components to allow proper fork clearance.
Tighten bolt with the included Allen wrench.
STEP 4: Reinstall front wheel
and check clearance between
fender and tire. There must be a
minimum of 2 inches between
the tire and the fender. If you do
not have this clearance, fender
use is not recommended.
STEP 1
Fits 18.5 to 22.2 mm (3/4-7/8”)
Fits 22.2 to 25.4 mm (7/8-1”)
Fits 31.8 to 34.5 mm (1 ¼ -1 ”)
23 64
STEP 3
We make quality products and they include a limited lifetime warranty to the
original owner of our products. These fenders are warranted to be free from
defects in materials and workmanship for as long as the original purchaser
owns the product. This warranty does not cover damage due to accident,
abuse, or normal wear and tear. This warranty is void if the fenders or fender
mounting hardware are modified, or are not properly installed on a bicycle for
which they were designed. To make a claim under this warranty, return the
fenders together with proof of purchase, to the retail dealer from which they
were purchased, or contact Planet Bike directly.
Purchaser’s sole remedy pursuant to this warranty is for
Planet Bike to repair or replace the faulty part(s). Planet
Bike provides no other warranty, expressed or implied.
This warranty gives you specific legal rights; you may
also have other rights which vary from state to state.
• Check toe overlap (touching your pedal/foot on the fender or wheel while turning
handlebars). If there is interference between your toe and front wheel, we do not
recommend using these fenders.
• Check for interference with other bike components, especially brakes, drive train,
and suspension forks. If interference is present readjust fenders. If interference
remains, do not use the fenders.
• There must be a minimum clearance of 2 inches between the tire and fender. If
you do not have this clearance, fender use is not recommended.
• Failure to follow installation instructions can result in loss of control, damage,
personal injury or death.
• Check fender installation before each ride to ensure hardware is tight and in
good condition and fender is centered over tire with a minimum of 2 inches of
clearance.
• These fenders are not intended for competitive use or excessive speeds.
• To keep the fenders functioning safely, replace worn parts as needed. Small parts
can be found at www.planetbike.com/rebuild
• If you are unsure of any part of the installation process please consult a
certified bicycle mechanic or local bike shop.
*For the most up to date installation instructions, go to
www.planetbike.com/page/support/manuals
ANGLE ADJUSTMENT KNOB
2”
2”
2”
STEP 1
