background image

 

 

                                     D 6 K 4         D 10 K 4         D 14 K 2

 

 

 

Before using the amplifiers, be sure to read the USER MAMUAL carefully. Please keep this 

USER MANUAL for future reference.

 

 NOTE

 

Warning:  The  inside  of  the  product  shell  has  non-insulated  dangerous 
voltage, which produces a electric shock to the body, so the amplifier must 
be connected to a grounded socket outlet.

 

Power amplifiers are capable of producing hazardous output voltages. To avoid electrical shock, do 

not touch any exposed speaker wiring while the amplifier is operating. The external wiring 
connected to the speaker terminals shall be installed by a qualified instructed person or ready-
made leads or cords of appropriate capacity shall be used. In addition, the speaker terminal 
should  be  covered  with  productive  cover  complying  with  the  security  operations  and 

requirements of the electrical products. 

 

The amplifier is very powerful and can be potentially dangerous to both loudspeakers and humans 
alike.  Many  loudspeakers  can  be  easily  damaged  or  destroyed  by  overpowering  them.  Always 
check the speaker's continuous and peak power capabilities. Although the amplifier's attenuators 
can be used to reduce the overall  gain,  an increase of the input signal  can result in  full output 
power, which may cause damage to connected speakers.

 

The device will emit radio frequency energy. So this product uses radio frequency energy and if not 

used  or  installed  in  accordance  with  these  operating  instructions,  may  cause  interference  to 
other  equipment,  such  as  radio  and  TV  receivers.  However,  there  is  no  guarantee  that 
interference will not  occur in  a particular installation.  If this equipment  does cause harmful 
interference to radio or TV reception, which can be determined by turning the equipment on 

and off, 

 

The  user  is  encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the  following 

measures:

 

▲ 

Reorient or relocate the antenna.

 

▲ 

Increase the separation between the equipment and receiver.

 

▲ 

Connect  the  equipment  to  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 

  

      

Connected.

 

▲ 

Consult the dealer or an experienced radio or TV technician for help.

 

Do not remove top or bottom covers. Removal of the covers will expose hazardous voltages. 
The user can not repair the internal parts, please contact with the qualified professional person 
for help. 

 

USER MANUAL

 

NOTE

 

NOTE

 

NOTE

 

Summary of Contents for D10K4














Reviews: