Piusi CUBE B.SMART Installation, Use And Maintenance Manual Download

Page: 11 / 60

/124

/60

This manual belongs to PIUSI S.p.A. The reproduction of all or parts is prohibited.

CUBE

EN (translated from Italian)

APPLY THREAD

SEALANT

TO THE

CONNECTORS

BEFORE FINAL

ASSEMBLY

MACHINE AND MANUFACTURER IDENTIFICATION

The CUBE B.SMART stations are equipped with an identification plate

attached to the frame:

- Model

- Serial number / year of manufacture

- Technical data

- CE marking

- Manual code

IMPORTANT

Before installation, always check that the dispensing system model

is correct and suitable for the supply currently available (Voltage /

Frequency).

8.1

POSITION OF THE PLATES

Some stickers and/or plates are applied to the distribution system to

indicate the most relevant information to the operator. It is necessary to

check that these do not deteriorate or detach over time.

NOTE

Should this occur, please contact our customer assistance office so

that we can send you copies of the spoilt or missing plates/labels for

reapplication where originally provided.

The following labels are present:

OFF

- Pump operation plate.

Summary of Contents for CUBE B.SMART





























































Search results

Summary of Contents for CUBE B.SMART

Reviews:

Related manuals for CUBE B.SMART

Brands by name

Popular brands

Piusi CUBE B.SMART, Installation, Use And Maintenance Manual

Search results

Summary of Contents for CUBE B.SMART

Reviews:

Related manuals for CUBE B.SMART

Brands by name

Popular brands