Pitney Bowes Relay 2500 User Manual Download | Manualshive

Page: 58 / 182

background image

About Linked Feeding

Linked feeding can only be set on the main sheet feeder on non-scanning jobs. With linked feeding,
sheets are initially fed from the main sheet feeder. When that feeder is empty, the inserter automatically
switches feeding from the second sheet feeder.

While the job is running with linked feeding enabled, above the inserter model on the touchscreen the
display shows:

1 > 2 > 1

. This confirms feeding automatically switches between feeders.

About the Manual Feed Option

l

The manual feed setting allows you to run stapled sets of up to five sheets - a maximum of 100 lbs.
(400 gsm) per set. The maximum compressed thickness of the set after folding must not exceed
0.08 inches (2 mm).

l

The inserter waits for manual insertion of each set into sheet feeder 1, after which it will fold and
insert the set automatically.

l

When running manual feed mode, sheet feeder 2 becomes inoperable.

l

The manual feed option is only available when Accumulation is set to OFF.

Product Overview

Pitney Bowes

Relay™ 2500, 3500, 4500 User Guide

December, 2018

Page 51 of 174

«
...
56
57
58
59
60
...
»

Summary of Contents for Relay 2500























































































































































































Reviews:

No comments

Related manuals for Relay 2500

Brand: White Pages: 34

Brand: HIGHLEAD Pages: 35

Memory Craft 5500

Brand: Janome Pages: 83

Brand: LAI Games Pages: 54

Brand: Siruba Pages: 28

Firebase SG-Z1200

Brand: FROGGYS FOG Pages: 6

Brand: Powr-Flite Pages: 9

Brand: Karma Pages: 12

Brand: Janome Pages: 25

Brand: LAUREL Pages: 2

Brand: Laurel Metal Products Incorporated Pages: 4

Brand: Brother Pages: 8

Brand: Brother Pages: 40

Brand: Brother Pages: 2

Brand: Brother Pages: 2

Brand: Brother Pages: 2

Brand: Brother Pages: 4

Brand: Brother Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands