Pitney Bowes Relay 2500 User Manual Download

Page: 46 / 182

Setting the Batch Counter

Batch Counter On

- If the batch counter is turned on, it allows pre-defined batches of finished

mailpieces to be automatically processed. When the batch is complete, the inserter automatically
stops.

Batch Counter Off

- If the batch counter is not turned on, the display counter counts the number

of items processed until you tap

Reset Counter

. Tap the

Start

button to begin processing the

next batch of mailpieces.

To set the batch counter:

1. Tap the

and

–

buttons to toggle the batch mode to

Off

NOTE

: If the batch counter is set to on, the inserter prompts for batch quantity. The default

quantity is 50, but any value can be selected up to 999 by tapping the

and

–

buttons.

2. Tap the

button to accept the setting.

Product Overview

Pitney Bowes

Relay™ 2500, 3500, 4500 User Guide

December, 2018

Page 39 of 174

Summary of Contents for Relay 2500






















































































































































































Search results

Summary of Contents for Relay 2500

Reviews:

Related manuals for Relay 2500

Brands by name

Popular brands

Pitney Bowes Relay 2500, User Manual

Search results

Summary of Contents for Relay 2500

Reviews:

Related manuals for Relay 2500

Brands by name

Popular brands